Projectの設定
config用フォルダ作成
Project ExplorerでProjectを選択後、上のMenu BarよりProject -> Add New Folderでフォルダを作成する。名前は何でもOK。(作成しなくても良い)
sdk_config.hの取り込み
(SDK_PATH)/example/ble_peripheral/ble_app_beacon/pca10040/s132/config/sdk_config.hをProject配下に取り込み
custom_board.hの作成
Project配下にcustom_board.hを作成
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73 | // Shinobi Dev Board
#ifndef CUSTOM_BOARD_H
#define CUSTOM_BOARD_H
#define LEDS_NUMBER 1
#define LED_1 18
#define LEDS_LIST { LED_1 }
#define LEDS_ACTIVE_STATE 1
#define BSP_LED_0 LED_1
#define BUTTONS_NUMBER 1
#define BUTTON_0 16
#define BUTTONS_ACTIVE_STATE 0
#define BSP_BUTTON_0 BUTTON_0
#define BUTTONS_LIST { BUTTON_0 }
#define BUTTON_PULL NRF_GPIO_PIN_PULLUP
#define LEDS_INV_MASK 0
#define RX_PIN_NUMBER 9
#define TX_PIN_NUMBER 11
#define CTS_PIN_NUMBER 10
#define RTS_PIN_NUMBER 8
#define HWFC false
#define SPIS_MISO_PIN 20 // SPI MISO signal.
#define SPIS_CSN_PIN 21 // SPI CSN signal.
#define SPIS_MOSI_PIN 22 // SPI MOSI signal.
#define SPIS_SCK_PIN 23 // SPI SCK signal.
#define SPIM0_SCK_PIN 23u /**< SPI clock GPIO pin number. */
#define SPIM0_MOSI_PIN 20u /**< SPI Master Out Slave In GPIO pin number. */
#define SPIM0_MISO_PIN 22u /**< SPI Master In Slave Out GPIO pin number. */
#define SPIM0_SS_PIN 21u /**< SPI Slave Select GPIO pin number. */
#define SPIM1_SCK_PIN 29u /**< SPI clock GPIO pin number. */
#define SPIM1_MOSI_PIN 24u /**< SPI Master Out Slave In GPIO pin number. */
#define SPIM1_MISO_PIN 28u /**< SPI Master In Slave Out GPIO pin number. */
#define SPIM1_SS_PIN 25u /**< SPI Slave Select GPIO pin number. */
// serialization APPLICATION board
// UART
// this configuration works with the SPI wires setup
#define SER_APP_RX_PIN 20 // UART RX pin number.
#define SER_APP_TX_PIN 22 // UART TX pin number.
#define SER_APP_CTS_PIN 23 // UART Clear To Send pin number.
#define SER_APP_RTS_PIN 21 // UART Request To Send pin number.
// serialization CONNECTIVITY board
// UART
#if 0
#define SER_CON_RX_PIN 22 // UART RX pin number.
#define SER_CON_TX_PIN 20 // UART TX pin number.
#define SER_CON_CTS_PIN 21 // UART Clear To Send pin number. Not used if HWFC is set to false.
#define SER_CON_RTS_PIN 23 // UART Request To Send pin number. Not used if HWFC is set to false.
#else
// this configuration works with the SPI wires setup
#define SER_CON_RX_PIN 20 // UART RX pin number.
#define SER_CON_TX_PIN 22 // UART TX pin number.
#define SER_CON_CTS_PIN 21 // UART Clear To Send pin number. Not used if HWFC is set to false.
#define SER_CON_RTS_PIN 23 // UART Request To Send pin number. Not used if HWFC is set to false.
#endif
#define SER_CONN_ASSERT_LED_PIN LED_0
#define NRF_CLOCK_LFCLKSRC {.source = NRF_CLOCK_LF_SRC_XTAL, \
.rc_ctiv = 0, \
.rc_temp_ctiv = 0, \
.accuracy = NRF_CLOCK_LF_ACCURACY_20_PPM}
#endif
|
SEGGER_Flash.icfの取り込み
Project Explorer -> Add Existing FileからSEGGER_Flash.icfファイルを取り込み
Build Optionの設定
Project ExplorerでProject選択後、OptionsボタンからOption画面を開く。その後、左上のdrop-down listでPrivate ConfigurationのCommonを選択する
以下のOptionを設定する
Preprocessor -> Preprocessor Definitions
| Option |
| NRF52832_XXAB |
| BOARD_CUSTOM |